It’s not difficult to snake a tub drain. A plumbing snake, gloves, and basic cleaning supplies are required to clear a bathtub drain. The overflow plate is underneath the faucet and above the drain plug. Then, remove the two screws that hold it in place. Once you’ve removed the screws, use a pair of pliers to pry it out of the way.
Next, unscrew two more screws from the bottom. This will allow you to get at the clog. You’ll also need to remove a small piece of plastic that’s attached to the plug, so that you can remove it. Once you’re done with that, take a screwdriver and carefully pull it off. The plug should now be free.
Table of Contents
What is the best way to unclog my bathtub?
A pot of boiling water can be poured down the bathtub drain. The mixture of baking soda and vinegar should be poured into the drain. Wait 5–10 minutes if you want to insert the drain plug or close the filter. The drain needs to be flushed with another pot of water.
If you don’t have a shower drain, you can also use a garden hose to drain the water from the tub. Just make sure that the hose is long enough to reach all the way to the bottom of the sink.
How do you clear a slow bathtub drain?
The baking soda should be dumped into the drain. If everything goes according to plan, you should see a lot of froth.
Why is my bathtub not draining?
Soap scum, hair, bath bombs, and damaged pipes are some of the reasons a bathtub won’t drain. Plumbing problems can be fixed using boiling water, baking soda and vinegar, a plunger, and a drain cleaner. Bathtubs can also be a source of water-borne diseases, such as E. coli and salmonella. To prevent these infections, wash your hands thoroughly after using the bathroom.
What will dissolve hair in a drain?
Combining baking soda and vinegar is a natural way to dissolve hair clogs, without resorting to harsh chemicals. First, pour a cup of baking soda down the drain, and then after a few minutes, add a small amount of vinegar.
Can plunging make a clog worse?
When used correctly, plungers are an effective way to clear a drain or a toilet. It’s important to form a tight seal around the drain and plunge slowly.
Plunging too quickly or with too much force can prevent a tight seal from forming, making it more difficult to remove the plunger from the toilet bowl. Plungers can also be used to clean the inside of a sink or tub.
If you have a large sink, you may need to use two or three plungers to get the job done.
Can’t get the snake down the drain?
Too much force – When you’re trying to dislodge a blockage, it can be tempting to try and force a snake cable through the drain too fast. Sometimes the cable will bend back on itself if you force it. This will allow you to get a good grip on it and get it out of the way.
Don’t push too hard – You don’t want to over-extend your snake wire. You want it to be flexible enough that you can move it around, but not so flexible that it won’t hold its shape when you try to push it through a drain.
Can you snake a shower drain?
Sometimes the best way to unclog a shower drain is with a drain snake, sometimes called a manual auger or electric auger. You’ll need a power drill to run the snake if it’s electric. You have to turn the handle by hand to open the drain if it’s manual. The first is to cut a small hole in the bottom of the shower head.
This will allow the snake to pass through. You can also use a screwdriver to pry the top off the head, but be careful not to puncture it. Then, using a pair of pliers, remove the two screws that hold it in place. Once you’ve removed the screws, pull the entire head out. It should come out easily.
Can snaking a drain make it worse?
A drain snake is a simple and cheap way to fix a blocked pipe. These are supposed to be used by anyone to clear a drain. But if used improperly, drain augers could make the clog worse. If you jam the obstruction tighter, you could cause more damage to the pipe.
How do you snake a shower drain without a snake?
You can use a natural drain cleaner. 1 cup of baking soda and 1 cup of distilled white vinegar should be mixed together. First, pour boiling water down the drain to loosen it, then follow with the baking soda-vinegar mixture and wait 15 minutes. Rinse with more boiling hot water and drain.
If you don’t want to use vinegar, you can also use a mixture of 1/2 cup vinegar and 2 cups of water. Add the vinegar to the water, stir, and let sit for a few minutes before using.
